How to replace your iPod touch battery
11th Dec 2009 | 14:15
Don't pay Apple £66 to replace your first-gen battery - do it yourself!
Replace your iPod battery steps 1-9
Despite the iPod touch being one of the finest devices ever conceived by mankind, the sad truth is one day your beloved iPod will die. It could be a simple blunt trauma to the face or old-age gnawing at its lithium-ion polymer power cell, but either way the Grim Reaper is going to get it.
If you own a first generation (1G) iPod touch - released back at the end of 2007 – then it's likely its battery is on the way out. Generally after 500 charge cycles a Li-pol battery's actual capacity is less than 80 percent of its original, or worse depending on how it has been treated. On top of this its life beyond three years isn't good.
Apple charges £66 to replace these batteries, while you can pick up a shiny new battery on Ebay for less than £6. The question is should you try to replace one yourself? If you can solder, then perhaps. If you also don't mind wrestling open tightly sealed cases and are good with tools, then yes.
The hardest part is initially opening the iPod itself - it's well built and tricky to open. We've done it and we're human, so with our guide you should be able to as well.
Be aware this will void any warranty. The advice is given in good faith and it's up to you as an individual to judge the appropriateness of the information and whether you follow it or not.
Step 1: You will need:
- iPod touch 1G
- Replacement battery kit with safe-open pry tools
- Soldering iron
- Small flathead screwdriver
- Small crosshead screwdriver
Step 2: The easiest place to start is at the dock-end of the iPod. Take the pry tool and insert it between the metal back and the chassis above the dock connector. Once in slide it towards the side away from the headphone socket.
Step 3: This creates a small gap in the side between the chassis and metal back. Insert the small flathead screwdriver into this gap and gently pry along until there's an audible click. This is the case clip coming undone.
Step 4: At this point insert the second pry tool and work your way along this edge 'unclipping' the case. You may need to use the flathead screwdriver, but ideally stick with the pry tool to minimise any cosmetic damage.
Step 5: With one side free the top and final side are easy to release with the pry tools and the back can be totally removed.
Step 6: The battery is glued to the iPod using three black pads. Use the pry tool to carefully remove it, by working it along the sides. Be careful, there are two ribbon cables underneath it, we've displayed these on the image, so avoid these areas. Secondly don't bend the battery, this could internally short it can cause it to explode.
Step 7: With this the battery swings free, at this point it can be replaced. Skip to step 14 for soldering advice. However we're going to continue taking the iPod touch apart, in case you want to replace the screen or have problems removing the battery. So remove the screw underneath the battery leads and the one next to the headphone socket.
Step 8: Use a pry tool to remove the screen connector ribbon cable from the iPod touch's main circuit board.
Step 9: Use a pry tool to remove the digitiser connector from the circuit board and remove the two screws from this as well.
Replace your iPod battery steps 10-17
Step 10: Use a flathead screwdriver to carefully prise the wireless antenna circuit board from the chassis. Do this by gently edging it along the inside-edge of the board until it comes free.
Step 11: At the other end of the iPod remove the strip of tape and the two screw hiding beneath it.
Step 12: Using a pry tool gently free the main circuit board, which is glued to the chassis.
Step 13: With this the entire electronics caboodle can be swung up and out of the way. This reveals a final circuit board stuck to the chassis. Use a pry tool and the flathead screwdriver to gently free this from its gluey bondage. Be careful as this section is quite thin, it may also get caught against the screw holes.
Step 14: The electronics are now free, this makes it a doddle to unsolder the original battery pack. Be careful not to short circuit the black and red power wires, as potentially this can cause the battery to explode if left in that state. We placed masking tape over one wire until soldering was required. A quick touch of a soldering iron on each lead's solder point should remove them. Remember to responsibly recycle your battery rather than throwing it away.
Step 15: Clean the area of gunk, cut the new batteries' terminal wire to the correct lengths and tin the ends. Just 1mm of tinned wire will be enough. You'll probably want to add a blob of solder to the circuit board's solder points as well. With that solder each wire in place.
Step 16: Retrace each step in reverse order and your iPod touch should end up looking like this. We found the circuit boards generally needed to be angled into place to get the screw holes to correctly line up.
Step 17: Replace the back making sure it's clipped into place right around the body. Most batteries ship with a 40 percent charge so press the power button and hope everything goes well. Success! You'll need to reset the time and date but beyond that happy iPoding.
Liked this? Then check out How to turn an old laptop into a digital photo frame
Sign up for TechRadar's free Weird Week in Tech newsletter
Get the oddest tech stories of the week, plus the most popular news and reviews delivered straight to your inbox. Sign up at http://www.techradar.com/register